Skip to content

Air protection

Authorised emission measurement for air pollution sources

One-off emission measurement may, by law, only be carried out by an authorised person.

  • Authorised person
  • Accredited laboratory No. 1599
  • Report and ISPOP support
Measuring equipment at an industrial installation

Accredited laboratory No. 1599

View the documents

Measurements

From input documents to a usable report

Who may measure emissions

One-off emission measurement, expert reports, dispersion studies and verification of emission reports may, under Section 32 of Act No. 201/2012 Coll., only be carried out by an authorised person. Before ordering, check the scope of authorisation and accredited methods with every supplier.

What we measure

TZL, NOx, CO, SO₂, O₂, TOC and VOC, HCl and heavy metals within the accredited scope.

Service overview

Service details

Who may measure emissions

One-off emission measurement, expert reports, dispersion studies and verification of emission reports may, under Section 32 of Act No. 201/2012 Coll., only be carried out by an authorised person. Before ordering, check the scope of authorisation and accredited methods with every supplier.

What we measure

TZL, NOx, CO, SO₂, O₂, TOC and VOC, HCl and heavy metals within the accredited scope. The scope for your source is determined by the operating permit. From the permit, the stack diagram and the operating regime we verify what is to be measured and where.

How it works

The operator notifies the measurement date in ISPOP at least 5 working days in advance. We measure in representative operation of the source and data from the report are notified through ISPOP within 60 days. The report contains a description of the source, operating conditions, methods used, measured values and an evaluation against the limit.

Scope and deliverables

One-off emission measurement may, by law, only be carried out by an authorised person. We measure emissions from boiler plants, paint shops, dryers and other sources and help with notification in ISPOP.

What we measure within our accreditation

Within our accreditation we measure solid particulate matter (TZL) isokinetically, NOx, CO, SO₂ and O₂ with analysers, TOC and VOC, HCl and inorganic chlorine compounds, heavy metals (As, Be, Cd, Cr, Co, Cu, Mn, Ni, Pb, Sb, Se, Sn, Te, Tl, V, Zn, Al, Fe, Si, Hg) and gas moisture, velocity and volume flow. The specific scope is determined by the permit for your operation.

We use the same procedure for other sources: boiler plants, paint shops, dryers, biogas plants, diesel generator sets, wood-processing plants, electroplating shops and other technologies. You will find the overview under Facilities and technologies.

Price, timing and scope of measurement

Price and quote

The price depends on the number of sources and substances measured, the difficulty of the measuring points and the distance. Send us your documents and we will prepare a non-binding quote. We will get back to you within 24 hours.

Date and report

We agree the measurement date according to your operation and the authority's requirement. The delivery date of the report will be stated in the quote.

What determines the scope

The scope and frequency of measurement are not set by us, but by the operating permit, the authority's decision or a request from the hygiene station (KHS) or the Czech Environmental Inspectorate (ČIŽP). Send them to us and we will verify exactly what is required of you.

How a project works
  1. Review of documents

    We review your documents, authority requirements and propose the best approach.

  2. Scope and schedule

    We clarify the scope of measurements, studies or documentation and plan timing.

  3. Measurements and processing

    We carry out measurements, calculations or document preparation as agreed.

  4. Expert deliverable

    We deliver a report, study or documentation ready for the next permitting step.

Frequently asked questions

Who may carry out a one-off emission measurement?

Under the Air Protection Act, a one-off emission measurement may only be carried out by an authorised person. Before ordering, it is also advisable to verify the accredited scope of the methods used.

What do you need for a quote and for preparing the measurement?

Send the valid operating permit, the latest report, a technical description of the source and stacks, information on technology changes and the planned operating regime. Photographs of the measuring point also help.

Who announces the date and data in ISPOP?

The operator announces the date at least 5 working days before the measurement. The authorised person prepares the report and reports the measurement data through ISPOP within 60 days.

What is the difference between authorisation and accreditation?

Authorisation entitles a person to carry out activities defined by law. Accreditation confirms a laboratory's technical competence for specific methods and a defined scope of tests.

What do I need to have ready in ISPOP before the measurement?

The site must be registered in CRŽP. An authorised representative with authorisation set up in CRŽP can make the submission on the operator's behalf. We will go through the procedure with you before the date.

How much does emission measurement cost?

The price depends on the number of sources and substances measured, the measuring points and the distance. After receiving your documents we will prepare a non-binding quote.

How soon will I receive the report?

The delivery date of the report will be stated in the quote according to the scope of measurement. Data from the report are notified to ISPOP within 60 days using form F_OVZ_JME.

Do you measure throughout the Czech Republic?

Yes. We carry out on-site measurement of emissions, the working environment, noise and other quantities throughout the Czech Republic. We have offices in České Budějovice, Prague 5 and Havlíčkův Brod.

Legal and methodological sources