Workplace environment and KHS
Dust measurements in the workplace
We measure dust in workplace air, that is the inhalable and respirable fractions that employees are exposed to during real work.
- Inhalable and respirable fractions
- Accredited laboratory No. 1599
- Documents for KHS and job categorisation

Accredited laboratory No. 1599
View the documentsMeasurements
From a description of the operation to the dust report
What we assess for workplace dust
Dust is not a single parameter: the type of dust, the particle size and the composition all matter.
Workplace, stack or outdoor area
This service measures dust in workplace air, that is employee exposure.
Service details
What we assess for workplace dust
Dust is not a single parameter: the type of dust, the particle size and the composition all matter. Depending on the material and technology we assess whether the inhalable fraction (total concentration) is enough, or whether the respirable fraction and crystalline silica must be addressed as well.
Government Regulation No. 361/2007 Coll. distinguishes the limit PELc for total concentration (the inhalable fraction) and PELr for the respirable fraction. If the dust contains a fibrogenic component, the respirable fraction and the concentration of the fibrogenic component must always be determined.
Workplace, stack or outdoor area
This service measures dust in workplace air, that is employee exposure. Dust carried through a stack into the outdoor air is covered by emission measurement, and for open storage areas and the handling of bulk materials, depending on the area size, source classification, an operating permit, a dispersion study and operating rules may have to be addressed.
Typical examples are welding shops and wood processing operations, where two levels arise: employee exposure in the hall and emissions through the stack. Measurement in the breathing zone does not replace emission measurement at the stack, and vice versa.
Scope and deliverables
We measure dust in workplace air, that is the inhalable and respirable fractions that employees are exposed to during real work. You can use the result for the hygiene station (KHS), job categorisation, occupational health and safety and an assessment of extraction.
What we measure within our accreditation
Within our accreditation we measure the inhalable and respirable dust fractions, organic substances (benzene, toluene, xylene, styrene, acetates, chlorinated solvents), short-term chemical substances with detector tubes, microclimate, vibration, artificial lighting and noise in the working environment.
Price, timing and scope of measurement
Price and quote
The price depends on the number of sources and substances measured, the difficulty of the measuring points and the distance. Send us your documents and we will prepare a non-binding quote. We will get back to you within 24 hours.
Date and report
We agree the measurement date according to your operation and the authority's requirement. The delivery date of the report will be stated in the quote.
What determines the scope
The scope and frequency of measurement are not set by us, but by the operating permit, the authority's decision or a request from the hygiene station (KHS) or the Czech Environmental Inspectorate (ČIŽP). Send them to us and we will verify exactly what is required of you.
How a project works
Review of documents
We review your documents, authority requirements and propose the best approach.
Scope and schedule
We clarify the scope of measurements, studies or documentation and plan timing.
Measurements and processing
We carry out measurements, calculations or document preparation as agreed.
Expert deliverable
We deliver a report, study or documentation ready for the next permitting step.
Frequently asked questions
When is dust measurement in the workplace addressed?
Typically on a notice from the hygiene station (KHS), when classifying new jobs, after a substantial change of technology, or when the level of exposure cannot be reliably determined by estimate. We clarify the scope from the notice and the description of the operation.
What is the difference between total dust and the respirable fraction?
The total concentration (inhalable fraction) covers particles that can be inhaled through the nose or mouth. The respirable fraction is the part that penetrates into the deeper airways and the alveoli; for dust with a fibrogenic component, for example crystalline silica, it must always be determined.
Is total dust enough for our material?
It depends on the material and the technology. With concrete, stone, ceramics or bricks crystalline silica may be significant, with wood the species of wood, and with welding also the metals in the welding fumes; we propose the scope from the description of the operation.
Is this the same as measuring dust at a stack or at a storage area?
No. This service assesses employee exposure in workplace air; dust at a stack is addressed by emission measurement, and dust from open storage areas by a different procedure under air protection rules. We therefore first clarify which case you are dealing with.
Legal sources
- Act No. 258/2000 Coll., on Public Health Protection
Current wording in e-Sbírka: job categorisation (Section 37 et seq.), noise measurement (Section 32a) and noise in building proceedings (Section 77).
- Government Regulation No. 361/2007 Coll.
Conditions of health protection at work, including permissible exposure limits for dust (PELc, PELr).
